Demo and haul-off
We saw-cut, break out, and remove the old concrete, then haul it away. You do not need to rent a dumpster or find a disposal site. We leave the subgrade clean and ready for base prep.
Licensed
Licensed & Bonded
Fully Insured
Insured & Bonded
24/7 Emergency
Same-Day Response
Warranty Backed
9+ Years Trusted in Clairemont
What our Concrete Pouring & Finishing service includes
Every pour we do includes the full scope: demo if needed, base prep, forming, reinforcement, placement, finishing, and cure. You are not hiring three different trades and hoping they coordinate. One crew owns the whole job. Add-ons like decorative finishes, sealing, and staining are quoted separately so you only pay for what you want.
Base prep and compaction
We excavate to depth, compact the native soil, and bring in 4 inches of compacted base rock. A slab poured over loose or organic soil will settle and crack. This step is where most cheap jobs cut corners, and it is where we do not.
Forming and reinforcement
We set forms to finished grade with a laser level and tie rebar or wire mesh on chairs so the steel sits mid-slab. We use a form release agent so forms strip clean. This is what gives the slab its shape, thickness, and strength.
Placement and consolidation
We place the mix with a pump or by hand depending on access, then consolidate it with a vibrator to remove air pockets. We screed to grade and check the slope. A 400-square-foot slab takes about two to three hours from first truck to screed.
Finishing and joint cutting
We float, edge, groove, and apply the finish you chose, whether that is broom, salt, or hard trowel. Control joints get cut within 24 hours. We cover the slab to cure for 5 to 7 days, then come back and strip the forms.
Final walkthrough and cure guidance
We walk the finished slab with you, point out the joints and slope, and tell you exactly when to use it. Stay off it for 7 days, keep vehicles off for 28. We also tell you when to seal it, usually around the 28-day mark.
What Concrete Pouring & Finishing in Clairemont, California involves
Concrete Pouring & Finishing in Clairemont, California is the trade of placing mixed concrete into formed, reinforced areas and working the surface to a specified texture and slope. It covers everything from a 12x12 patio slab to a driveway apron, a garage floor, or a foundation pour. We mix or order 3,000 to 4,500 PSI concrete, screed it flat, float it, edge it, and cut control joints before the mix sets. Get the timing wrong and you get cracking, scaling, or a puddle against your garage door.
Most Clairemont calls we take are replacements, not brand-new builds. Driveways from the 1960s and 70s have spalled, settled, or cracked through, and patching only buys a season or two. Homeowners searching for concrete placement near me Clairemont usually want one crew to demo the old slab, haul it off, re-grade the base, and pour fresh. We also pour new patios, walkways, pool decks, and garage floors. If you want the best concrete pouring contractor in Clairemont CA, ask for a crew that handles forming, placement, and finishing under one license.
How our concrete pouring and finishing process works
Five steps, one crew, no handoffs. Here is exactly what happens from the first call to the day we pull the forms.
01
Schedule
Call or book online — a real human picks up and confirms a 2-hour arrival window.
02
Diagnose
Licensed tech inspects on-site, then walks you through the cause and your options.
03
Fix
The job is completed to code and done right the first time — no shortcuts, no surprises.
04
Guarantee
Every job backed by a written workmanship warranty — and we stand behind it.
Tools and methods we use on every pour
Tools & Equipment
Concrete mixer and concrete pump
We batch on site or order ready-mix, and use a pump for tight-access backyards where a truck cannot reach. Pumps save hours on patios and pool decks.
Power trowel and hand floats
Power trowels give garage floors and interior slabs a hard, smooth finish. Hand floats and edgers handle the edges and smaller patios where a machine will not fit.
Concrete saw and groover
We cut control joints within 24 hours with a concrete saw, and use hand groovers on smaller slabs. Joints control where the concrete cracks.
Laser level and screed
A laser level keeps forms and finished grade accurate. Screeds strike off the concrete to grade so the slab is flat and drains correctly.
Concrete vibrator
We consolidate the mix with a vibrator to remove air pockets around rebar and forms. That is how you avoid honeycombing and weak spots.
Quikrete and Sakrete mixes
For small repairs and patch work we use Quikrete and Sakrete bagged mixes. For full pours we spec ready-mix at 3,500 to 4,500 PSI with admixtures.
Sika and Euclid Chemical admixtures
We use Sika and Euclid Chemical admixtures to control set time, improve workability, and add air entrainment for exterior slabs that face coastal moisture.
Methods & Standards
ACI-certified finishing practices
Our finishers follow ACI standards for placement, consolidation, finishing, and curing. That means the right slump, the right timing on floating and troweling, and a cure period that lets the concrete reach its design strength.
Control joint layout at 2 to 3 times slab thickness
A 4-inch slab gets joints every 8 to 10 feet, a 5-inch slab every 10 to 12 feet. We plan the joint layout before we pour so the cuts land in straight lines and the slab cracks where we want it to.
Air-entrained mixes for exterior flatwork
We spec air entrainment in exterior mixes to handle freeze-thaw cycles and coastal moisture. It is a small cost add that prevents scaling and spalling down the road.
Wet curing for 5 to 7 days
We cover the slab and keep it wet for 5 to 7 days so the concrete cures at the right rate. Fast curing causes shrinkage cracks. Slow curing builds strength.
California code-compliant forming and reinforcement
We build forms and place rebar to California code for thickness, cover, and setbacks. If your job needs a permit, we pull it and we build it to pass inspection the first time.
When Clairemont homeowners call us
01
A 1960s driveway in North Clairemont is cracked through and pooling water at the garage door.
What we do: We demo the old slab, re-grade the base, and pour a new 4-inch reinforced driveway with a broom finish and control joints every 8 to 10 feet. We set the slope to move water to the street.
→ A level, drain-correct driveway that handles two cars and looks new. Most jobs are done in three days.
02
A Bay Park homeowner wants a patio poured before summer for entertaining.
What we do: We form and pour a 300-square-foot patio with rebar, a light salt finish, and a slope away from the house. We coordinate the pour around their schedule and cure it for 7 days.
→ A finished patio ready for furniture in about a week, with a surface that stays cool and grippy.
03
A Clairemont Mesa rental property has a walkway with three lifted panels and a trip hazard.
What we do: We saw-cut the bad panels, re-pour them to match the existing thickness and finish, and re-establish the grade so water runs off. We keep the good panels and only replace what failed.
→ A safe, even walkway at a fraction of a full replacement cost. One-day job in most cases.
04
A homeowner on Mount Streets needs a new garage floor after years of oil stains and spalling.
What we do: We demo the old slab, compact the base, and pour a 5-inch hard-troweled garage floor with a slight slope to the door. We cut joints to control cracking and seal it after cure.
→ A smooth, durable floor that resists oil and tire marks and is easy to sweep clean.
How Concrete Pouring & Finishing works in Clairemont
Clairemont sits close enough to the coast that we get marine moisture most mornings, and warm inland afternoons the rest of the day. That swing matters for concrete. We pour earlier in the day when temperatures are cooler, and we use air-entrained mixes and cure blankets to control how fast the slab dries. Most of the housing stock here went up in the 1950s through the 1970s, which means the driveways and patios we replace are original. They were poured thin, often without rebar, and they have settled with the soil. We see a lot of cracking, spalling, and poor drainage on those older slabs. When you hire us for concrete placement and finishing Clairemont work, we fix the base, not just the surface. That is why our pours hold up. If you are pricing concrete pouring and finishing cost in Clairemont California, remember that the base prep is most of the difference between a slab that lasts 10 years and one that lasts 40.
Neighborhoods We Serve
-
North Clairemont
Older driveways with shallow base and no rebar are common. We usually add 4 inches of compacted base rock and rebar on these replacements.
-
Bay Park
Closer to the water, so we spec air-entrained mixes and pay extra attention to drainage away from the house and patio edges.
-
Clairemont Mesa
A mix of single-family homes and rentals. We do a lot of driveway and walkway replacements here, often with tight access that calls for a pump.
-
Mount Streets
Long driveways and sloped lots. We set the fall carefully so water moves to the street and not toward the garage or a neighbor's property.
-
Kearny Mesa
More commercial and industrial concrete work, including garage floors and loading areas that need a hard-troweled, high-PSI finish.
Local Conditions We Plan For
-
Coastal marine layer and morning moisture
Slows surface drying and can cause finishing problems if we pour too late in the day. We start early and adjust the mix to compensate.
-
Warm inland afternoons in summer
Accelerates cure and raises the risk of plastic shrinkage cracks. We use cure blankets and keep the slab wet for the full cure period.
-
Expansive clay soils in parts of Clairemont
Soil movement cracks slabs that were poured thin or without reinforcement. We excavate deeper and add compacted base rock to isolate the slab from soil movement.
-
Older housing stock with original flatwork
Most slabs we replace are 40 to 60 years old and were poured without rebar. We upgrade to rebar or wire mesh on every replacement pour.
North Clairemont driveway replacement
Concrete problems we fix for Clairemont homeowners
Old concrete fails in predictable ways. Here are the problems we see most often on Clairemont slabs and how we fix them so they do not come back.
Problem
Cracked and settled driveway slabs
Water pools at the garage door, the surface trips you every time you walk out, and the cracks keep widening with each wet season.
Our Fix
We demo the failed slab, fix the base that caused the settling, and pour a new reinforced slab with control joints cut at the right spacing. You get a level, crack-controlled surface that drains away from the house.
Problem
Spalling and scaling surfaces
The top layer flakes off, leaving a rough, gravelly surface that is hard to shovel and looks worn out. It gets worse every winter.
Our Fix
We remove the failed surface, prep the slab, and either re-pour the section or apply a bonded overlay. We spec an air-entrained mix for exterior work so the new surface handles freeze-thaw and coastal moisture.
Problem
Uneven surfaces and trip hazards
Walkway panels that have lifted or dropped become a liability, especially for kids and older family members. It is also a code issue if the city inspects.
Our Fix
We cut out the uneven panels, re-establish the grade, and pour replacements that match the existing finish. For sound slabs that just lifted, we can sometimes mudjack or lift them instead of a full replacement.
Problem
Poor drainage around patios and pool decks
Water sits against the house or in the pool deck, which leads to foundation moisture, slippery surfaces, and long-term damage to the slab and the structure.
Our Fix
We set the correct fall during the pour, usually 1/8 inch per foot away from the structure, and add a drain or channel if the site needs it. We check the slope with a laser level before we finish.
Problem
Efflorescence and staining
White mineral deposits and stains make a newer slab look old and neglected. It is a sign that water is moving through the concrete.
Our Fix
We clean the surface, address the moisture source, and apply a breathable concrete sealer. Sealing blocks water and salts from soaking in while still letting the slab dry out. Reapply every 3 to 5 years.
Why Clairemont homeowners pour new concrete
A new pour fixes drainage, kills trip hazards, and adds usable outdoor space. Here is what you actually get when the job is done correctly.
-
Drainage that works
We set a 1/8-inch-per-foot fall away from your house and toward the street or a drain. That slope is the difference between a dry garage floor and water pooling at the door every winter. Poor drainage is the number one complaint we hear on old Clairemont slabs.
-
Cracks that stay closed
We use rebar or wire mesh on chairs, cut control joints within 24 hours, and keep joints spaced at 2 to 3 times the slab thickness in feet. A 4-inch slab gets joints every 8 to 10 feet. That is how you control where concrete cracks instead of letting it crack wherever it wants.
-
A finish built for traffic
Broom finish for driveways and walkways, light salt finish or smooth trowel for patios, hard-troweled for garage floors. We match the finish to how you use the surface. A driveway needs grip when wet; a patio needs to feel good barefoot. One finish does not fit every slab.
-
Adds real property value
A clean, level driveway or patio is one of the first things a buyer sees. Cracked, settled concrete reads as deferred maintenance and invites low offers. Fresh concrete pouring patio Clairemont projects routinely return more at resale than the pour cost, especially on Mount Streets homes with long driveways.
Concrete Pouring & Finishing pricing in Clairemont
Typical 2026 pricing for residential concrete pouring and finishing in Clairemont runs $8 to $14 per square foot for standard flatwork, including demo, base prep, rebar, pour, and finish. A 400-square-foot driveway usually lands between $3,200 and $5,600. Decorative finishes, stamped concrete, and tight-access jobs cost more because they take more labor and materials. We give you a written, line-item price the same day so you can see exactly where the money goes. No hidden fees, no surprise change orders.
Typical Investment Range
$3,200 - $5,600 for a typical 400-square-foot driveway; $8 - $14 per square foot for standard flatwork
You are paying for base prep, reinforcement, and a proper cure, not just a concrete truck. Those three things are why our slabs do not crack and settle like the cheap bids do. A pour that lasts 30 years costs less per year than one that fails in 8.
What changes the price
01
Square footage and thickness
A 4-inch patio slab costs less per square foot than a 6-inch driveway apron or a foundation pour. More concrete, more base, and more labor all scale with size and depth.
02
Demo and haul-off
If we are removing an old slab, that adds cost for saw-cutting, breaking, loading, and disposal fees. A clean site with no demo is cheaper. We quote demo as a separate line so you can see it.
03
Access and pump needs
A backyard pour with no truck access needs a concrete pump, which adds a few hundred dollars. Wide-open front driveways do not. We tell you upfront if a pump is required.
04
Finish type
A standard broom finish is the most affordable. Salt finish, exposed aggregate, stamped concrete, and decorative stains add labor and materials. We show you samples and price each option.
05
Base conditions and soil
Soft or expansive soil may need deeper excavation and more base rock. If we find roots, old footings, or bad fill during demo, we tell you before we proceed and adjust the price.
06
Reinforcement and admixtures
Rebar, wire mesh, and admixtures like air entrainment and accelerators add material cost but improve performance. We spec what the job needs, not what is cheapest.
Licensed, certified, and reviewed
Licensed & Certified
- California Contractor License (C-8) — issued by California Contractors State License Board
- ACI Certification — issued by American Concrete Institute
- OSHA 30 — issued by Occupational Safety and Health Administration
- NRMCA Certification — issued by National Ready Mixed Concrete Association
Verified Reviews
Google ★★★★★4.9
Poured a new driveway and walkway for us in North Clairemont. The crew was on time, cleaned up daily, and the finish is perfect. They cut the control joints exactly where they said they would. Water runs away from the house now instead of into the garage. Highly recommend.
Yelp ★★★★★4.8
We had a patio poured in Bay Park and could not be happier. They gave us a written estimate the same day, started when they said, and finished on schedule. The salt finish looks great and the slope keeps water off the house. Fair price and no surprises.
BBB ★★★★★4.9
Used them for a garage floor replacement at a rental property. They demoed the old slab, fixed the base, and poured a hard-troweled floor that looks great. The price came in under two other bids and the work passed inspection without any issues. Will use again.
Google ★★★★★5.0
Replaced a cracked walkway with three lifted panels. They matched the existing finish so well you cannot tell where the repair starts. One-day job, no mess left behind, and the trip hazard is gone. Straightforward pricing and good communication throughout.
Concrete expertise you can check
We have been pouring concrete in Clairemont since 2017, which is 9 years of driveways, patios, walkways, pool decks, and foundations across the 92117 and 92111 ZIPs. Our finishers hold ACI certification and our crews are OSHA 30 trained, so they know what a safe pour looks like and what a bad mix looks like before it sets. We carry a California Contractor License (C-8) for concrete work. We have poured everything from 200-square-foot walkway repairs to full driveway replacements, and we still cut our own control joints.
- 9 years pouring concrete in Clairemont and the surrounding 92117 and 92111 neighborhoods
- ACI-certified finishers who know slump, air entrainment, and cure timing
- California Contractor License (C-8) for concrete work, bonded and insured
- OSHA 30 trained crews on every job site, every day
- We pour in 3,000 to 4,500 PSI mixes and spec admixtures for local conditions
What Clairemont clients say
Real experiences from customers who chose our Concrete Pouring & Finishing services.
“We had a 50-year-old driveway that was cracked and pooling water at the garage door. The crew demoed it, re-graded the base, and poured a new 500-square-foot slab in three days. The broom finish is even, the joints are straight, and the water runs to the street now. Price was fair and they cleaned up every day.”
M
Mark R.
Homeowner, North Clairemont
“I needed a new patio poured before a family party. They gave me a written estimate the same day, started the following week, and finished on schedule. The salt finish looks great and the slope keeps water off the house. They even re-set a sprinkler line they hit during demo. No extra charge, no drama.”
S
Sandra L.
Homeowner, Bay Park
“I manage a few rentals and I have used these guys on three driveways and a walkway. They show up when they say, they pour a clean slab, and they cut the control joints right. The last driveway was 600 square feet and it came in under what the other bids quoted. I will keep calling them.”
D
Dave M.
Property Owner, Clairemont Mesa
Frequently Asked Questions
Real answers to the questions we hear most often from local homeowners and property managers.
How much does concrete pouring and finishing cost in Clairemont?
Most residential pours in Clairemont run $8 to $14 per square foot in 2026, including demo, base prep, rebar, pour, and finish. A 400-square-foot driveway typically lands between $3,200 and $5,600. Decorative finishes, stamped concrete, and tight-access jobs push the number higher. We give you a written price the same day so there is no guessing.
How long does concrete placement take in Clairemont California?
A standard driveway or patio is a two-to-three-day job: one day for demo and base, one day for forming and pour, and a partial day for finishing and joint cutting. The concrete itself sets in 24 to 48 hours, but you should stay off it for 7 days and keep vehicles off for 28 days. Cure time is not optional if you want it to last.
What is the best concrete mix for pouring in California?
For exterior flatwork in Clairemont we spec a 4,000 PSI mix with air entrainment and a low water-to-cement ratio, usually around 0.45. That mix handles our coastal moisture and temperature swings without scaling or spalling. For garage floors and interior slabs, a 3,500 PSI mix is plenty. We adjust the mix for the pour, not the other way around.
Do I need a permit for concrete pouring in Clairemont?
Usually not for a driveway, patio, or walkway replacement at the same size and location. You do need a permit for structural work, retaining walls over 4 feet, and any pour that changes drainage or grade toward a neighboring property. We check with the city before we start and pull whatever is required. That is part of the job, not an extra.
Related Services
Concrete Driveway Installation
A new driveway starts with the same pour and finish work we do every week. We form, reinforce, pour, and broom-finish the slab, then cut control joints so it drains away from your garage. Most Clairemont driveways are 400 to 600 square feet and take two to three days.
View Concrete Driveway InstallationConcrete Driveway Repair
Not every driveway needs a full replacement. If the damage is isolated to a few panels, we saw-cut the bad sections, re-pour them to match, and tie them into the existing slab. You get a level surface without paying for a whole new driveway.
View Concrete Driveway RepairConcrete Patio Installation
A patio pour is all about finish and slope. We set the fall away from the house, pour a 4-inch slab with rebar, and finish it smooth or with a light texture. Clairemont patios usually run 200 to 400 square feet and are ready for furniture in about a week.
View Concrete Patio InstallationConcrete Patio Repair
Settled or cracked patio slabs get replaced panel by panel. We match the existing finish and thickness so the repair disappears into the original pour. If the whole patio has failed, we can demo and re-pour it in the same footprint.
View Concrete Patio RepairConcrete Walkway & Sidewalk Installation
Walkways need a broom finish for grip and joints spaced to control cracking. We pour 4-inch slabs with wire mesh, set them at a consistent grade, and keep the width uniform. Most Clairemont front walkways are 3 to 4 feet wide and pour in a single day.
View Concrete Walkway & Sidewalk InstallationConcrete Walkway & Sidewalk Repair
Trip hazards and cracked panels are the usual call. We lift or replace the bad sections, re-pour to match, and re-establish the slope so water runs off instead of pooling. Small repairs are often a one-day job.
View Concrete Walkway & Sidewalk RepairContact Concrete Contractor Clairemont
Call us at +18446359999 or email [email protected] to schedule an estimate. We answer the phone Monday through Friday from 8:00 AM to 6:00 PM and return after-hours messages the next morning. Most estimates in Clairemont are scheduled within a day or two, and we give you a firm price before any work begins.
Concrete Contractor Clairemont
-
Phone
+18446359999 -
Address
Genesee Ave, San Diego, CA 92117, Clairemont, California
-
Hours
Mon–Fri: 7AM – 7PM
Sat: 8AM – 4PM
Sun: Emergency Only
24/7 Emergency Available